CCTVPLANNER.IO · NVR · REOLINK
Reolink Home Hub Pro
Wi-Fi 6 hub for up to 24 Reolink cameras including battery cams
SPECIFICATIONS · HOME HUB PRO
Full specifications
Specifications sourced from official manufacturer datasheet (link in hero).
About the Reolink Home Hub Pro
The Reolink Home Hub Pro is a pro-class recorder for installs that have outgrown a single 16-channel unit but do not yet justify dedicated rack-cabinet hardware — multi-floor offices, retail flagships, factory cells, light-industrial yards. Storage capacity sits in the comfort zone for month-long retention at typical channel resolutions, with room to drop archived footage onto cold storage as it ages out. The desktop chassis sits on a shelf, IT bench or wall-mount tray and runs cool enough that ventilation is not a serious design constraint. No PoE ports are built into the recorder, so cameras connect through a separate PoE switch. That is the preferred architecture on professional installs because a dedicated managed switch gives finer VLAN control, larger PoE budgets, and easier replacement than an integrated switch tied to the NVR chassis.
Best use cases for this recorder
Multi-floor office, flagship retail, factory cell
24 channels absorb the per-floor camera count of a 3-5 story building, a retail flagship with stockroom and yard, or a factory cell with overhead and process cameras — without forcing a second unit on day one.
Strengths
- •Compact chassis fits in a half-height comms cabinet or office bench
Considerations
- •No built-in PoE — budget for a separate managed PoE switch with appropriate per-port wattage for the planned cameras
- •Single HDD bay means no RAID protection — schedule regular backups or pair with a secondary NVR/NAS for redundancy
- •Codec support not declared in the datasheet — verify against the camera plan before commissioning to avoid CPU-bound transcoding
- •ONVIF support not declared — third-party cameras may need same-brand replacement or a brand-agnostic VMS instead of this recorder
Storage planning
Running all 24 channels at the industry-typical 4 Mbps/channel H.265 CBR (15 fps, 4 MP scene complexity), the Home Hub Pro produces roughly 1013 GB of footage per day — about 7088 GB/week, 30375 GB/month, and 91125 GB across a 90-day retention window. Fully populated with 1× 16 TB drives the unit holds 16 TB raw — enough for roughly 0.5× the one-month archive at full bitrate before RAID overhead. These figures are deterministic — derived from your bitrate assumption, the channel count, and the calendar — not estimated from a marketing data sheet.
Estimates assume 4 Mbps per channel H.265 CBR continuous recording. Motion-only recording typically reduces storage by 40-70%.
Installation tips for the Home Hub Pro
Locate on a shelf in a ventilated, lockable cupboard — desktop units pull dust through the chassis quickly when sat on a carpeted floor, and the HDDs need ambient temperatures under 30 °C for rated life.
Plan storage at roughly 1013 GB/day (≈30375 GB/month) for continuous H.265 recording at 4 Mbps/channel — match HDD capacity to the longest retention window the privacy policy or insurance contract demands.
Schedule weekly off-site backups (NAS, cloud, or sister NVR) since the single-bay design has no internal redundancy — a failed disk loses the entire archive.
Pair with a managed PoE switch sized for the camera plan — choose 802.3at (≤30 W/port) for typical IR-equipped bullets, 802.3bt (≤60-90 W/port) when PTZ or heated housings are in scope.
Power & rack
Power draw sits at roughly 35 W idle and around 35 W under full load (1-bay HDD activity). That dissipates approximately 119 BTU/hour of heat into the rack — size the comms-cabinet ventilation accordingly. On desktop placement, raise the unit on rubber feet or a vented tray rather than directly on carpet — the chassis pulls cooling air through bottom intakes and dust ingress is the primary cause of premature HDD failure.
Installer time & cost (rough estimate)
A typical EU integrator quotes 6-8 h of labour to commission the Reolink Home Hub Pro (approximately €270-€360 excluding hardware), broken down as physical install, HDD population, 24-channel discovery and IP/credential configuration, schedule + retention setup, motion / event rules per camera, mobile-app pairing, and a brief operator handover. Allow extra time for sites with non-standard network topology (multi-VLAN, multi-site bridges) or for migrations from a legacy DVR where camera streams must be re-addressed.
Indicative EU 2024-2025 pricing — actual quotes vary by region, network topology and migration scope. Excludes hardware, HDDs, transport, permits, and VAT.
Frequently asked questions
How many cameras can the Reolink Home Hub Pro record?
Up to 24 IP camera channels per chassis. The ingest bandwidth ceiling is not declared in the datasheet — confirm with the vendor before specifying high-bitrate (4K, 12 MP) cameras across all channels.
Does the Reolink Home Hub Pro support third-party (ONVIF) cameras?
ONVIF compliance is not declared in the official datasheet for this model — assume same-brand cameras only, or verify with the vendor before pairing it with non-Reolink hardware.
How much storage does the Reolink Home Hub Pro need for 30-day recording?
At the industry-typical 4 Mbps per channel H.265 CBR (15 fps, 4 MP scene), all 24 channels recording continuously for 30 days produces approximately 30375 GB (29.7 TB) of footage. Motion-only or event-triggered recording typically cuts that by 40-70 % depending on scene activity. Plan HDD capacity for the longest retention window your privacy policy or insurance contract demands.
What HDDs are recommended for the Reolink Home Hub Pro?
Use surveillance-rated HDDs — WD Purple, Seagate SkyHawk, Toshiba S300, or equivalent. Desktop / consumer drives (WD Blue, Seagate Barracuda) are not validated for 24/7 write workloads and typically fail within 12-18 months in CCTV use. Max 16 TB per bay across 1 bays = up to 16 TB raw capacity; populate matched pairs/sets if planning RAID.
Does the Reolink Home Hub Pro need its own PoE switch?
Yes — the recorder has no built-in PoE, so cameras connect through a separate managed PoE switch. Size the switch's PoE budget for the planned cameras: 802.3at (≤30 W/port) handles typical IR-equipped bullets and domes; 802.3bt (≤60-90 W/port) is needed for PTZ and heated housings.
What power and cooling does the Reolink Home Hub Pro need?
Plan for 35 W idle and ~35 W under full load, dissipating roughly 119 BTU/hour into the rack or cupboard. Size the UPS for at least 15-minute hold-up so the unit can flush write buffers and shut down cleanly on mains failure — abrupt power loss is the leading cause of NVR file-system corruption in commercial installs.
Is the Reolink Home Hub Pro suitable for evidentiary recording?
Depends on the retention and chain-of-custody policy. The 1-bay chassis is single-disk only; for evidentiary recording, pair with a secondary NVR or NAS for redundancy. On the export side, ensure footage is hashed and timestamped before transfer to investigators.
Related Reolink NVRs
Compare with similar-channel NVRs from other brands
Helpful Tools & Resources
Storage Calculator
Match HDD capacity to your retention policy
Bandwidth Calculator
Verify your network can carry the ingest load
Camera Quantity Calculator
Match channel count to your site
UPS Sizing Calculator
Hold-up time for clean NVR shutdown on mains failure
System Budget Estimator
Hardware + install + commissioning cost
CCTV Storage Planning Guide
Bitrate, retention, RAID — the full math
Plan your CCTV layout with Reolink Home Hub Pro
Use our free CCTV planner to lay out cameras feeding this recorder, match HDD capacity to retention windows, and generate a professional PDF report — no signup required.
Free until you outgrow it · No card · No install