CCTVPLANNER.IO · NVR · DAHUA
Dahua XVR1B04
4-ch Penta-brid 1080N/720p Cooper 1U — 4 analog + 5 IP overlay, 1 SATA (6 TB)
SPECIFICATIONS · XVR1B04
Full specifications
Specifications sourced from official manufacturer datasheet (link in hero).
About the Dahua XVR1B04
The Dahua XVR1B04 is a small-channel NVR aimed at home, shop-front and small-office sites — the channel count caps the project naturally at a domestic-scale install. On-board storage tops out in single-digit TB — suitable for short retention windows (one to two weeks) at moderate channel counts. Plan an external NAS or eSATA expansion if the privacy policy or insurance contract requires longer retention. A single rack-unit slim chassis keeps the install footprint minimal and leaves headroom in the cabinet for a PoE switch, UPS and patch panel above it. No PoE ports are built into the recorder, so cameras connect through a separate PoE switch. That is the preferred architecture on professional installs because a dedicated managed switch gives finer VLAN control, larger PoE budgets, and easier replacement than an integrated switch tied to the NVR chassis.
Best use cases for this recorder
Residential & home installations
With 4 channels and 1-bay storage, the XVR1B04 fits the typical home or villa install — front door, garage, garden, driveway. Single-disk recording at SMB bitrates covers 2-4 weeks of retention.
Strengths
- •Smart H.265+ codec halves storage cost over H.265 at equivalent perceived quality
- •ONVIF compliance lets the unit record from third-party cameras, not just the same-brand catalog
- •Hybrid HD-CVI/AHD/TVI inputs let legacy analog cameras share the recorder with new IP cameras — useful for staged retrofits
- •Compact chassis fits in a half-height comms cabinet or office bench
Considerations
- •No built-in PoE — budget for a separate managed PoE switch with appropriate per-port wattage for the planned cameras
- •Single HDD bay means no RAID protection — schedule regular backups or pair with a secondary NVR/NAS for redundancy
- •Channel count caps install at small-site scale — verify the camera plan does not push past the channel limit during phased expansion
- •No RAID support — single-disk failure means losing all footage on that disk; plan retention policy accordingly
Storage planning
Running all 4 channels at the industry-typical 4 Mbps/channel H.265 CBR (15 fps, 4 MP scene complexity), the XVR1B04 produces roughly 169 GB of footage per day — about 1181 GB/week, 5063 GB/month, and 15188 GB across a 90-day retention window. Fully populated with 1× 6 TB drives the unit holds 6 TB raw — enough for roughly 1.2× the one-month archive at full bitrate before RAID overhead. These figures are deterministic — derived from your bitrate assumption, the channel count, and the calendar — not estimated from a marketing data sheet.
Estimates assume 4 Mbps per channel H.265 CBR continuous recording. Motion-only recording typically reduces storage by 40-70%.
Installation tips for the XVR1B04
Install in a standard 19-inch rack cabinet on supported rack rails; allow at least 1U of clearance above and below the 1U for airflow and HDD-bay servicing.
Plan storage at roughly 169 GB/day (≈5063 GB/month) for continuous H.265 recording at 4 Mbps/channel — match HDD capacity to the longest retention window the privacy policy or insurance contract demands.
Schedule weekly off-site backups (NAS, cloud, or sister NVR) since the single-bay design has no internal redundancy — a failed disk loses the entire archive.
Pair with a managed PoE switch sized for the camera plan — choose 802.3at (≤30 W/port) for typical IR-equipped bullets, 802.3bt (≤60-90 W/port) when PTZ or heated housings are in scope.
Power & rack
Power draw sits at roughly 35 W idle and around 35 W under full load (1-bay HDD activity). That dissipates approximately 119 BTU/hour of heat into the rack — size the comms-cabinet ventilation accordingly. Allow 1U of cabinet space for the chassis plus 1U of unobstructed airflow above and below; pair with a UPS sized for at least 15-minute hold-up so the recorder shuts down cleanly on mains failure.
Installer time & cost (rough estimate)
A typical EU integrator quotes 5-7 h of labour to commission the Dahua XVR1B04 (approximately €225-€315 excluding hardware), broken down as physical install, HDD population, 4-channel discovery and IP/credential configuration, schedule + retention setup, motion / event rules per camera, mobile-app pairing, and a brief operator handover. Allow extra time for sites with non-standard network topology (multi-VLAN, multi-site bridges) or for migrations from a legacy DVR where camera streams must be re-addressed.
Indicative EU 2024-2025 pricing — actual quotes vary by region, network topology and migration scope. Excludes hardware, HDDs, transport, permits, and VAT.
Frequently asked questions
How many cameras can the Dahua XVR1B04 record?
Up to 4 IP camera channels per chassis. The ingest bandwidth ceiling is not declared in the datasheet — confirm with the vendor before specifying high-bitrate (4K, 12 MP) cameras across all channels.
Does the Dahua XVR1B04 support third-party (ONVIF) cameras?
Yes — ONVIF Profile S/T support means the unit records from third-party cameras as well as the same-brand catalog. Most cameras supporting ONVIF 16.12 or newer plug-and-play; older firmware may require manual stream URL configuration in the NVR web UI.
How much storage does the Dahua XVR1B04 need for 30-day recording?
At the industry-typical 4 Mbps per channel H.265 CBR (15 fps, 4 MP scene), all 4 channels recording continuously for 30 days produces approximately 5063 GB (4.9 TB) of footage. Motion-only or event-triggered recording typically cuts that by 40-70 % depending on scene activity. Plan HDD capacity for the longest retention window your privacy policy or insurance contract demands.
What HDDs are recommended for the Dahua XVR1B04?
Use surveillance-rated HDDs — WD Purple, Seagate SkyHawk, Toshiba S300, or equivalent. Desktop / consumer drives (WD Blue, Seagate Barracuda) are not validated for 24/7 write workloads and typically fail within 12-18 months in CCTV use. Max 6 TB per bay across 1 bays = up to 6 TB raw capacity; populate matched pairs/sets if planning RAID.
Does the Dahua XVR1B04 need its own PoE switch?
Yes — the recorder has no built-in PoE, so cameras connect through a separate managed PoE switch. Size the switch's PoE budget for the planned cameras: 802.3at (≤30 W/port) handles typical IR-equipped bullets and domes; 802.3bt (≤60-90 W/port) is needed for PTZ and heated housings.
What power and cooling does the Dahua XVR1B04 need?
Plan for 35 W idle and ~35 W under full load, dissipating roughly 119 BTU/hour into the rack or cupboard. Size the UPS for at least 15-minute hold-up so the unit can flush write buffers and shut down cleanly on mains failure — abrupt power loss is the leading cause of NVR file-system corruption in commercial installs.
Is the Dahua XVR1B04 suitable for evidentiary recording?
Depends on the retention and chain-of-custody policy. The 1-bay chassis is single-disk only; for evidentiary recording, pair with a secondary NVR or NAS for redundancy. On the export side, ensure footage is hashed and timestamped before transfer to investigators.
Related Dahua NVRs
Compare with similar-channel NVRs from other brands
Helpful Tools & Resources
Storage Calculator
Match HDD capacity to your retention policy
Bandwidth Calculator
Verify your network can carry the ingest load
Camera Quantity Calculator
Match channel count to your site
UPS Sizing Calculator
Hold-up time for clean NVR shutdown on mains failure
System Budget Estimator
Hardware + install + commissioning cost
CCTV Storage Planning Guide
Bitrate, retention, RAID — the full math
Plan your CCTV layout with Dahua XVR1B04
Use our free CCTV planner to lay out cameras feeding this recorder, match HDD capacity to retention windows, and generate a professional PDF report — no signup required.
Free until you outgrow it · No card · No install