CCTVPLANNER.IO · CAMERA · MILESIGHT
Milesight MS-C2162-FIPNA
Bullet Camera with 1.2MP (1280×960) resolution, 88° field of view, and 25m IR night vision range.
SPECIFICATIONS · MS-C2162-FIPNA
Specifications
Verified specifications sourced from the official manufacturer datasheet.
View official datasheetAre you the manufacturer of this camera?
Verify the specifications of your Milesight models and earn the "Confirmed by the manufacturer" badge, shown on these pages and next to your cameras inside the planner installers design with. Free of charge.
About the Milesight MS-C2162-FIPNA
The Milesight MS-C2162-FIPNA is a weather-sealed bullet housing optimized for perimeter, parking, and exterior building installations. 720p HD resolution captures enough detail for basic identification only at close range: on the same lens it reaches about two thirds of the distance a 1080p camera does, and loses face detail beyond that. Medium IR range (20-40 m) is appropriate for typical residential driveways, small commercial perimeters, and back-of-house loading bays where reach beyond ~30 m is rarely needed at night. A wide 80-120° angle covers a large room or open area from a single mounting position, making it ideal for retail floors, conference rooms, and small parking lots.
Best use cases for this camera
Entrance, lobby & vestibule
The 88° field of view captures the entire entrance and surrounding waiting area from a single ceiling mount. Useful for capturing visitors as they enter and leave.
Strengths
Considerations
- •Resolution limits forensic digital zoom; recorded faces beyond ~12m may not be identifiable
Coverage at Different Distances
| Distance | Coverage Width | Coverage Area | Use Case |
|---|---|---|---|
| 5m | 9.7m | 48 m² | Entrance, corridor |
| 10m | 19.3m | 193 m² | Room, retail aisle |
| 15m | 29.0m | 435 m² | Warehouse, parking row |
| 20m | 38.6m | 773 m² | Parking row, courtyard |
| 30m | 57.9m | 1738 m² | Parking lot, yard |
| 50m | 96.6m | 4828 m² | Perimeter, large area |
Field of View Visualization
Night Vision Performance
Daytime
Full 1.2MP (1280×960) resolution at 88° field of view. Effective identification range up to 3m in good lighting conditions.
Nighttime (IR)
Built-in IR LEDs illuminate up to 25m in complete darkness. Switches to B/W mode for clear night footage.
Installation tips for the MS-C2162-FIPNA
Pair with low-cost ambient lighting (motion-triggered LED floods) to extend usable identification distance beyond the IR limit.
Position so the most important subject (entrance, cash register, gate) is in the center third of the frame, because peripheral pixel density drops with wide angles.
Coverage geometry & DORI distances
At a 5-metre standoff the Milesight MS-C2162-FIPNA covers about 9.7 m of scene width; at 10 m that grows to 19.3 m, and at 20 m to 38.6 m. Translating those numbers through EN 62676-4 pixel-density thresholds, the camera can detect a person up to 27 m, observe up to 11 m, recognise up to 5 m, and produce Identify-level detail (250 px/m in the EN 62676-4 DORI scale) up to 3 m. Effective range above the identify threshold relies on supplementary lighting or a longer-focal-length optic; the geometry above assumes the 3-10.5mm lens declared by the manufacturer.
Power & cabling
The Milesight MS-C2162-FIPNA draws an estimated 7.5 W under typical load (with the IR illuminator engaged where applicable), placing it in the 802.3af (Class 3, ≤15.4 W) budget. A single switch port supplies enough power without an injector. Cabling: stick to Cat6 STP for runs up to 100 m end-to-end; beyond that, add an inline PoE extender or move to fibre with a media converter at the camera end. On outdoor runs, route through ø25 PVC or PE conduit to keep the cable shielded from UV and rodents.
Privacy & legal (GDPR / RODO)
Any camera operating in a publicly accessible area falls under GDPR (RODO in Poland). Art. 13 obliges the data controller to post an information sign at every entry point with controller name, DPO contact, lawful basis (typically Art. 6(1)(f) legitimate interest for property protection), purpose, and retention period. Even a narrowly-aimed bullet camera can incidentally record passers-by, so the Art. 13 sign at the entry point applies regardless of how tightly the lens is framed.
Installer time & cost (rough estimate)
A typical EU installer quotes 3-4 h of labour per bullet camera of this class (approximately €135-€185 excluding hardware), broken down as bracket mounting, cable termination at both ends, on-site commissioning, and a brief operator handover. Allow extra time for high mounts (>4 m), exterior installations requiring scaffolding, or sites where cable routing demands wall penetrations or conduit work.
Indicative EU pricing at 2024-2025 rates; actual quotes vary by region, mounting height, and site conditions. Excludes hardware, transport, permits, and VAT.
Frequently asked questions
Is the Milesight MS-C2162-FIPNA suitable for outdoor installation?
Yes for the IP66/IP67-rated variant of this model. Bullet and dome bodies in the Milesight range survive direct rain, snow and UV; check the IP / IK rating against your environment (IP66 for rain/dust, IK10 for vandal-prone locations).
What PoE class powers the Milesight MS-C2162-FIPNA?
The camera draws roughly 7.5 W in steady-state operation, requiring an 802.3af (Class 3, ≤15.4 W) switch port. A single Cat6 STP cable carries both data and power up to 100 m; beyond that, add an inline extender or convert to fibre near the camera.
How much storage does the Milesight MS-C2162-FIPNA consume per day?
At 1.2MP (1280×960) resolution, 15 fps H.265 continuous recording, the MS-C2162-FIPNA produces approximately 5 GB per day, about 150 GB per month. Motion-only or event-triggered recording typically cuts that by 40-70 % depending on scene activity. Plan NVR HDD capacity for the longest retention period required by your privacy policy or insurance contract.
Up to what distance can the Milesight MS-C2162-FIPNA identify a person?
By the DORI thresholds of EN 62676-4 (Identify at 250 px/m on the target, a density the 2025 edition calls Characterise), this camera reaches Identify level up to about 3 m, recognises a person up to 5 m, observes general activity up to 11 m, and detects motion up to 27 m. Identification distance assumes daylight or full IR illumination on the target; at the limits of the IR cone the effective identify distance shrinks roughly 30 %.
What network bandwidth does Milesight MS-C2162-FIPNA use?
Typical ingest is 2 Mbps for the main stream (H.265, medium scene complexity, 15 fps) plus ~0.5 Mbps for a low-resolution sub-stream used by mobile clients. For a 16-camera installation of this class, plan a 50-100 Mbps NVR uplink and a dedicated VLAN for camera traffic.
Related Milesight Bullet Cameras
Other Milesight cameras
Helpful Tools & Resources
Free CCTV Design Tool
Plan a full camera layout online, no download, free to start
Camera Placement Tool
Position cameras on a real floor plan and see live DORI coverage
FOV Calculator
Calculate field of view for any focal length
Storage Calculator
Estimate HDD requirements for your setup
Camera Quantity Calculator
Find out how many cameras you need
Field of View Explained
Understand HFOV, VFOV, and lens selection
Camera Placement Guide
Best practices for positioning cameras
All Features
See everything CCTVplanner can do
Plan your layout with Milesight MS-C2162-FIPNA
Use our free CCTV planner to place this camera on your floor plan, see real-time field of view coverage, and generate a professional PDF report.
Free until you outgrow it · No card · No install