CCTVPLANNER.IO · NVR · QNAP
QNAP QGD-1602P
Smart edge PoE++ switch + NAS/NVR hybrid with 2.5GbE and 10GbE uplinks (QVR Pro up to 128 ch)
SPECIFICATIONS · QGD-1602P
Full specifications
Specifications sourced from official manufacturer datasheet (link in hero).
About the QNAP QGD-1602P
The QNAP QGD-1602P is a mega-channel NVR aimed at sites that would otherwise need clustered storage — airports, stadiums, multi-site retail, transport hubs. Internal HDD capacity covers the most common retention windows (30-60 days at typical SMB bitrates). For installations bound to longer holds, the unit accepts external storage via eSATA / iSCSI without sacrificing channel count. In desktop form factor the unit installs in a back-office, server cupboard or small comms rack — no rack rails required and fan noise stays in the office-acceptable band. Partial built-in PoE (16 ports for 128 channels) handles the closest cameras directly and pushes the remainder onto an external PoE switch. This split is common when the NVR sits near a cluster of cameras and the far cameras are reached through a switch in another room or floor.
Best use cases for this recorder
Campus, factory, logistics & critical infrastructure
At 128 channels per chassis, the unit consolidates what would otherwise be 2-4 mid-range NVRs into a single rack appliance. Useful where licensing per-chassis matters and where consolidating storage onto one RAID set simplifies forensic retrieval.
Strengths
- •128-channel headroom absorbs phased expansion without forcing a second chassis
- •16 built-in PoE ports eliminate the need for an external switch on small installs
- •RAID 0/1/50/60/JBOD support protects archive against single-disk failure
- •H.265 codec roughly halves storage cost over legacy H.264 installs
- •ONVIF compliance lets the unit record from third-party cameras, not just the same-brand catalog
Considerations
- •Maximum per-channel resolution not declared in the datasheet — confirm with the vendor before specifying high-MP cameras
Storage planning
Running all 128 channels at the industry-typical 4 Mbps/channel H.265 CBR (15 fps, 4 MP scene complexity), the QGD-1602P produces roughly 5400 GB of footage per day — about 37800 GB/week, 162000 GB/month, and 486000 GB across a 90-day retention window. These figures are deterministic — derived from your bitrate assumption, the channel count, and the calendar — not estimated from a marketing data sheet.
Estimates assume 4 Mbps per channel H.265 CBR continuous recording. Motion-only recording typically reduces storage by 40-70%.
Installation tips for the QGD-1602P
Locate on a shelf in a ventilated, lockable cupboard — desktop units pull dust through the chassis quickly when sat on a carpeted floor, and the HDDs need ambient temperatures under 30 °C for rated life.
Plan storage at roughly 5400 GB/day (≈162000 GB/month) for continuous H.265 recording at 4 Mbps/channel — match HDD capacity to the longest retention window the privacy policy or insurance contract demands.
Distribute high-power cameras (PTZ, heated housings) across the 16 built-in PoE ports — concentrating them on a single port group can exceed the per-port PoE budget even when the chassis total has headroom.
Patch the recorder uplink into a switch port matching its native speed (the network panel exposes 2× 10GbE SFP+, 8× 2.5GbE RJ-45, 8× 1GbE RJ-45) — running a 10 Gb chassis through a 1 Gb uplink throttles playback and multi-stream review.
Power & rack
Power draw sits at roughly 40 W idle and around 355 W under full load (2-bay HDD activity plus 370 W of PoE delivered to cameras). That dissipates approximately 1211 BTU/hour of heat into the rack — size the comms-cabinet ventilation accordingly. On desktop placement, raise the unit on rubber feet or a vented tray rather than directly on carpet — the chassis pulls cooling air through bottom intakes and dust ingress is the primary cause of premature HDD failure.
Installer time & cost (rough estimate)
A typical EU integrator quotes 19-21 h of labour to commission the QNAP QGD-1602P (approximately €855-€945 excluding hardware), broken down as physical install, HDD population and RAID set-up, 128-channel discovery and IP/credential configuration, schedule + retention setup, motion / event rules per camera, mobile-app pairing, and a brief operator handover. Allow extra time for sites with non-standard network topology (multi-VLAN, multi-site bridges) or for migrations from a legacy DVR where camera streams must be re-addressed.
Indicative EU 2024-2025 pricing — actual quotes vary by region, network topology and migration scope. Excludes hardware, HDDs, transport, permits, and VAT.
Frequently asked questions
How many cameras can the QNAP QGD-1602P record?
Up to 128 IP camera channels per chassis. The ingest bandwidth ceiling is not declared in the datasheet — confirm with the vendor before specifying high-bitrate (4K, 12 MP) cameras across all channels.
Does the QNAP QGD-1602P support third-party (ONVIF) cameras?
Yes — ONVIF Profile S/T support means the unit records from third-party cameras as well as the same-brand catalog. Most cameras supporting ONVIF 16.12 or newer plug-and-play; older firmware may require manual stream URL configuration in the NVR web UI.
How much storage does the QNAP QGD-1602P need for 30-day recording?
At the industry-typical 4 Mbps per channel H.265 CBR (15 fps, 4 MP scene), all 128 channels recording continuously for 30 days produces approximately 162000 GB (158.2 TB) of footage. Motion-only or event-triggered recording typically cuts that by 40-70 % depending on scene activity. Plan HDD capacity for the longest retention window your privacy policy or insurance contract demands.
What HDDs are recommended for the QNAP QGD-1602P?
Use surveillance-rated HDDs — WD Purple, Seagate SkyHawk, Toshiba S300, or equivalent. Desktop / consumer drives (WD Blue, Seagate Barracuda) are not validated for 24/7 write workloads and typically fail within 12-18 months in CCTV use. Match drive capacity across bays if planning RAID — mixed capacities default to the smallest disk size per stripe.
Does the QNAP QGD-1602P need its own PoE switch?
Not on small installs — 16 built-in PoE ports power and connect cameras directly to the recorder. On larger sites a dedicated managed PoE switch is still the cleaner architecture: separate failure domain, larger PoE budget, easier replacement.
What power and cooling does the QNAP QGD-1602P need?
Plan for 40 W idle and ~355 W under full load, dissipating roughly 1211 BTU/hour into the rack or cupboard. Size the UPS for at least 15-minute hold-up so the unit can flush write buffers and shut down cleanly on mains failure — abrupt power loss is the leading cause of NVR file-system corruption in commercial installs.
Is the QNAP QGD-1602P suitable for evidentiary recording?
Depends on the retention and chain-of-custody policy. The 2-bay chassis supports basic mirroring on the install side, but lacks declared RAID 5/6 parity — verify with the vendor whether RAID is supported in newer firmware On the export side, ensure footage is hashed and timestamped before transfer to investigators.
Related QNAP NVRs
Compare with similar-channel NVRs from other brands
Helpful Tools & Resources
Storage Calculator
Match HDD capacity to your retention policy
Bandwidth Calculator
Verify your network can carry the ingest load
Camera Quantity Calculator
Match channel count to your site
UPS Sizing Calculator
Hold-up time for clean NVR shutdown on mains failure
System Budget Estimator
Hardware + install + commissioning cost
CCTV Storage Planning Guide
Bitrate, retention, RAID — the full math
Plan your CCTV layout with QNAP QGD-1602P
Use our free CCTV planner to lay out cameras feeding this recorder, match HDD capacity to retention windows, and generate a professional PDF report — no signup required.
Free until you outgrow it · No card · No install